龙骨：吊杆和轻钢龙骨，吊架与龙骨之间的距离应为一。在顶部展开眼睛并固定所有衣架。衣架的下口与钩子相连，然后主龙骨在钩子的中间固定。调整高度螺母，使主龙骨底板底板平面线为3cm并紧固。然后是龙骨的安装。根据实际安装长度减小5mm截取所需的截断龙骨，设置三角吊架，根据图纸要求，将所有截断的起重机临时连接到主龙骨上。
主机：根据加热型主机安装位置的图纸设计，以主机板代替模板，确认主机安装的准确位置，然后将主机主体固定在龙骨顶部。
顶部对齐和口面板：顶部对齐，确定在哪里安装灯具，在哪里安装厨房和卫生间用具，提前排队。扣板，这个环节直接关系到天花板的整体效果。不仅要光滑，还要做直缝。
拐角线：安装必须平稳牢固，确定安装高度并画出水平线。做好瓷砖粘贴后，将水平的情况下，将天花板集成支撑边角，紧紧地固定在瓷砖上，做到没有明显的缝隙。
扣板：戴干净手套，安装扣板，兼顾两侧整体美观和对称。固定模板，用切割器和直尺描绘三次以上，用剪刀将边缘切割成90度，用双手折叠2-3次即可。板切割口的对应表面卡在龙骨中，切割口位于接收侧杆上，并将夹持位置拉出以收紧模板。此时，三角吊架可以用钢钳和主龙骨拧紧。当安装模板的中间部分时，模板的两个对应表面分别被夹在扶手中，从而控制模板之间的间隙并保持接缝线。
Keel: suspender and light steel keel, the distance between hanger and keel should be one to. Expand the eye at the top and fix all the hangers. The hanger's lower mouth is connected with the hook, and then the main dragon skeleton is in the middle of the hook and fixed. The height nut is adjusted to make the floor plane of the main keel bottom to the plane line 3cm and fasten. Then, it is the installation of the keel. In accordance with the actual installation length reduced 5mm to intercept the required truncated keel, set the triangle hanger, according to the drawing requirements, all the truncated cranes are temporarily attached to the main keel.
Host: in accordance with the drawing design of the heating type host installation position, take the host panel instead of the template to confirm the accurate location of the host installation; and then put the main body of the host on the top of the dragon bone fixed.
Top alignment and mouth panel: Top alignment, determine where to install lamps and lanterns, where to install kitchen and toilet appliances, line up in advance. Buckle panel, this link is directly related to the overall effect of the ceiling. Not only to be smooth, but also to make a straight seam.
The corner line: the installation must be smooth and firm, determine the installation height and draw the horizontal line. After doing a good job of pasting ceramic tiles, the level of the case, will be integrated ceiling supporting edges and corners, tightly fixed in the ceramic tile, to do without obvious gaps.
Buckle plate: wear clean gloves, install the buckle plate to consider the overall beauty and symmetry on both sides. Fixed the template, with a cutter and ruler to depict more than three times, with scissors to cut the edges into 90 degrees, folding with hands 2-3 times can be. The corresponding surface of the plate cutting mouth is stuck in the dragon bone, the cutting mouth is on the receiving side bar, and the clip position is pulled out to tighten the template. At this time, the triangle hanger can be tightened with the steel tongs and the main keel. When the middle part of the template is installed, the two corresponding surfaces of the template are respectively clamped in the Fu keel, so as to control the gap between the templates and keep the seam line.
合肥装修建材网：http://www.zhuangxiujiancaiw.com/
教您轻松安装集成吊顶浴霸
楼梯下的三角空间利用如何装修设计才算合理利用？
浅谈重竹地板优缺点和铝包木门窗
窗帘挂球分类与作用和浴室灯位置与颜色的选择
中空玻璃内置百叶窗特性和家用天花灯的选择
窗帘装客在阳台的优缺点和中空玻璃内置百叶窗优点
皮质沙发清洁小窍门和打开鞋柜有异味的解决办法
浅谈百叶窗种类和百叶窗帘四点选购技巧需
玻璃门地弹簧保养技巧和安装厨房置物架的安装要点
玻璃门地弹簧更换方法和各种鞋柜的样式